retroreflective array sensor error proofing and light-guided assembly ? rugged metal frame with 225 mm (8.9 in) or 500 mm (19.7 in) sensing length; 1.5 m (4.9 ft) sensing range using included retroreflective tape (up to 6 m (20 ft) range when used with multi- ple brt-84x84a retroreflectors) ? highly visible green pick arrow ? red mis-pick arrow ? flexible mounting options; rugged steel mounting brackets ? fast response timeexcellent for part detection applications warning: not to be used for personnel protection never use this device as a sensing device for personnel protection. doing so could lead to serious injury or death. this device does not include the self-checking redundant circuitry necessary to allow its use in personnel safety applications. a sensor failure or malfunction can cause either an energized or de- energized sensor output condition. models model number description cable output pvl225p 225 mm (8.9 in) length, with up to 1.5 m (4.9 ft) separation between sensor and retroreflective tape (included) 2 m (6.5 ft), 4 wire unterminated cable pnp pvl225n npn pvl225pq 2 m (6.5 ft), cable terminated in 12 mm qd pnp pvl225nq npn pvl500p 500 mm (19.7 in) length with up to 1.5 m (4.9 ft) separation between sensor and retroreflective tape (included) 2 m (6.5 ft), 4 wire unterminated cable pnp PVL500N npn pvl500pq 2 m (6.5 ft), cable terminated in 12 mm qd pnp PVL500Nq npn pvl parts verification array p/n 165037_web rev. d 1/11/2013 http://www..net/ datasheet pdf - http://www..net/
dimensions l1 l2 model l1 l2 pvl225 311.5 mm (12.26 in) 327.5 mm (12.89 in) pvl500 592 mm (23.31 in) 608 mm (23.94 in) wiring diagram npn 12-30v dc job light enable < 1.0v dc C + 1 3 2 4 load pnp 12-30v dc job light enable > 7.0v dc C + 1 3 2 4 load color key 1 = brown 2 = white 3 = blue 4 = black note: pin 5 (center) is not used. installation multiple sensors located farther than the sensor's maximum range from one another are unlikely to cause crosstalk problems. however, when multiple sensors are mounted in a confined area, take care to avoid crosstalk between them. make sure that the sensor's beams fall in the center of the reflector. pvl parts verification array 2 www.bannerengineering.com - tel: 763-544-3164 p/n 165037_web rev. d http://www..net/ datasheet pdf - http://www..net/
correct alignment reflector sensor incorrect alignment reflector sensor status indicators/troubleshooting output indicator power indicator pick/mis-pick indicator indicator condition description #1 steady yellow output is active off output is inactive #2 steady green power is on and system is ok off power is off specifications supply voltage 12 to 30v dc (10% maximum ripple) supply current pvl225: < 140 ma max current at 12v dc (exclusive of load) < 70 ma max current at 30v dc (exclusive of load) pvl500: < 220 ma max current at 12v dc (exclusive of load) < 100 ma max current at 30v dc (exclusive of load) supply protection circuitry protected against reverse polarity and transient voltag- es output rating maximum load: 150 ma on-state saturation voltage: pnp: < 2v at 10 ma dc; < 2.5v at 150 ma dc npn: < 1.5v at 10 ma dc; < 2.0v at 150 ma dc off-state leakage current: <10 a at 30v dc indicators job ("pick") indicator: green mis-pick indicator: flashing red green led: power on/off yellow led: output on/off output response time less than 2 milliseconds on and off connections 2m (6.5 ft) pvc integral cable with unterminated, or 2m (6.5 ft) cable with 12 mm qd minimum object detection size 0.2 distance (meters) minimum object size object width (mm) 0 50.0 60.0 70.0 80.0 90.0 100.0 110.0 120.0 0.4 0.6 0.8 1.0 1.2 1.4 1.6 environmental rating ip50 operating conditions temperature: 0o to +50o c (+32o to +122o f) humidity: 90% at 50o c max. relative humidity (non- condensing) storage: -40o to +70o c (-40o to +158o f) construction housing: aluminum anodized translucent dome: polycarbonate vibration and mechanical shock all models meet mil. std. 202f requirements method 201a (vibration: 10 to 60 hz max., double amplitude pvl parts verification array p/n 165037_web rev. d www.bannerengineering.com - tel: 763-544-3164 3 http://www..net/ datasheet pdf - http://www..net/
beam spacing 70 mm pvl225: 4 beams pvl500: 8 beams sensing range 1.5 m (4.9 ft) with retroreflective tape 0.06 in. maximum acceleration 10g). also meets iec 947-5-2; 30g 11 ms duration, half sine wave. certifications quick-disconnect (qd) cordsets 4-pin threaded m12/euro-style cordsets model length style dimensions pinout mqdc-406 1.83 m (6 ft) straight 44 typ. ? 14.5 m12 x 1 2 3 4 1 1 = brown 2 = white 3 = blue 4 = black mqdc-415 4.57 m (15 ft) mqdc-430 9.14 m (30 ft) mqdc-450 15.2 m (50 ft) mqdc-406ra 1.83 m (6 ft) right-angle 32 typ. [1.26"] 30 typ. [1.18"] ? 14.5 [0.57"] m12 x 1 mqdc-415ra 4.57 m (15 ft) mqdc-430ra 9.14 m (30 ft) mqdc-450ra 15.2 m (50 ft) mounting brackets smbpvl1 ? right-angle bracket for mounting the pick-to-light array ? 7 mm mounting hole ? 14 gauge cold rolled steel 18 18 18 a c b a = ? 3, b = ? 7, c = ? 4.8 smbpvl2-225 ? flat bracket for mounting reflector inside bin ? 7 mm mounting hole ? 14 gauge cold rolled steel ? includes retroreflective tape 2 x ?7 29 348 smbpvl2-500 ? flat bracket for mounting reflector inside bin ? 7 mm mounting hole ? 14 gauge cold rolled steel ? includes retroreflective tape 2 x ?7 29 628 smbpvl3-225 ? right-angle bracket for mounting reflector outside bin ? 7 mm mounting hole ? 14 gauge cold rolled steel ? includes retroreflective tape 26 2 x ?7 31 342 pvl parts verification array 4 www.bannerengineering.com - tel: 763-544-3164 p/n 165037_web rev. d http://www..net/ datasheet pdf - http://www..net/
smbpvl3-500 ? right-angle bracket for mounting reflector outside bin ? 7 mm mounting hole ? 14 gauge cold rolled steel ? includes retroreflective tape 26 2 x ?7 31 622 smbpvl4 ? 28 mm tubular mount bracket for mounting out- side bin ? clearance for m6 (1/4 in) hardware ? painted cold rolled steel a c b 32 33 68 a = ? m6 1, b = ? m6 1, c = ? 28 smbpvl5 ? 28 mm tubular mount bracket for mounting in- side bin ? clearance for m6 (1/4 in) hardware ? painted cold rolled steel 32 41 51 a a = ? m6 1 iso 6h retroreflectors model reflectivity factor range size replacement tape brt-thg-1-100 0.7 1.5 m (4.9 ft ) 25 mm (1 in) wide 2.5 m (8.2 ft) long long range reflectors brt-84x84a 2.0 6 m (19.7 ft) 84x84 mm banner engineering corp limited warranty banner engineering corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. banner engineering corp. will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty period. this warranty does not cover damage or liability for misuse, abuse, or the improper application or installation of the banner product. this limited warranty is exclusive and in lieu of all other warranties whether express or implied (in- cluding, without limitation, any warranty of merchantability or fitness for a particular purpose), and whether arising under course of performance, course of dealing or trade usage. this warranty is exclusive and limited to repair or, at the discretion of banner engineering corp., replacement. in no event shall banner engineering corp. be liable to buyer or any other person or entity for any extra costs, expen- ses, losses, loss of profits, or any incidental, consequential or special damages resulting from any product defect or from the use or inability to use the product, whether arising in contract or war- ranty, statute, tort, strict liability, negligence, or otherwise. banner engineering corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product previously manufactured by banner engineering corp. pvl parts verification array http://www..net/ datasheet pdf - http://www..net/
|
